Ford Bantam Questions Any type

  • Newest
  • Recently Active
  • Unanswered

Ford Bantam My Battery Light Has Been Going On For A While And Doesn't Want...

Ford bantam My battery light has been going on for a while and doesn't want to switch off, While i am driving. I replaced the alternator but the light is still on. What might the problem be?

Camshaft

Camshaft

Hi I would just like to know if I can put a 1.6 rocam camshaft in my 1.3 rocam

Wipers

Where Do I Find The Alternator Relay

Crankin/scratching Noise When Reversing

Hi I have a 2006 Ford bantam rocam, there is terrible noise happening when the car is reversing & apply brakes it crank like 2 metal or rusted irons scrach each other it comes from front left side t...

Ford Bantum

I have a Ford Bantum Rocam 1.3 it’s doesn’t want to rev but ones I remove the plug for the map sensor it revs and black smoke coming from the exhaust please help what’s wrong with my car

Overheating

Hi my 1.3 ford bantam is getting hot,no water leaks. change thermostat and waterpump,no water in oil mixing everything looks ok. Motor is running good just getting hot. Is it head gasket and do i ...

Rocam 1.3 2003 Model

My car was mixing water and oil. Took it to the engineers. The top engine was skimmed. The rings, valves and timing chain were replaced. Now when it starts it cant hold power. The foot needs to be...

30

Missfire

Good day 2002 Ford Bantam 1300 Rocam I have changed coil pack, plugs, TP censor and still it missfire 2500 and 4500 RPM what can I do or charge to fix it

Firering Order Ford Bantam Coil Pack 1.3 I Rocam

Leaking Fuel , Water And Bakkoe Is Overheating. Ford Rocam 1.6

Hi we just replaced the head gasket on bakkie , but now there seem to be a whole lot of trouble with it . After the gasket were replaced they started the bakkie it started but oil leaking from the ...

Fuel With Water

Water mix with patrol

Bantam Start Failure

Hi i drive a 2005 1.3 bantam rocam . When its starts i can drive it no problem when i switch it of then it doest want to start again . e left it over night and this morning started up no problem. ...

Clutch Too Hard

Hi Unclear, I have put a new master clutch cylinder, slave cylinder,clutch kit. Clutch is too hard and inside are engaging but the car is not taking them. Ford bantam rocam engine 1.6 whatcould be...

Inner Cv

I bought a new complete drive shaft of my bantam roacam, it's still noise on the inner cv. I went to 4 mechanics. No one get it right. My car is a Roacam 2005. My email :mkgarimetsa2005@yahoo.com

Ford Bantam Engine Cranking But Not Sparking And Starter Not Turning Please...

hi i have got ford bantam 1.3 2006 cranking but not sparking and stater not turning, but when touching with wire does turn fuel pump working ,please assist how to sort the problem

Indicate Lights

Indicate lights are on and off on my ford bantam 2010 TDCI. What may be the reason?

Gauges Slow To Move

Good day, Ford Bantam 1.3 Rocam 2006.....when I start my bakkie, or put in petrol, all the gauges takes a few seconds (sometimes longer) before it starts to register and for the fuel needle to go up...

How To Adjust Handbrake

Shortcuts

Ford Bantam Experts

  • #1
    Guru97FK8
    Reputation
    3,670
  • #2
    Janus Welgemoed
    Reputation
    940
  • #3
    AB Zaviour
    Reputation
    820
View All

Find great deals from top-rated dealersTM

Search

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.