Ford Bantam Questions Any type

  • Newest
  • Recently Active
  • Unanswered
SiyabongaN
10

Hi Guys I Have Ford Bantam Leisure 1600i 2001 Model The Car Uses Too Much P...

66 views with 2 answers (last answer 10 months ago)
dyllen96
10

I Have A Ford Bantam 2002 I Cant Seem To Get My Braks Fuction Right Every ...

Ive replaced master celinder brake pads brake discs and fleud please help

58 views with 11 answers (last answer 3 days ago)
Theo_2012
0

Hi All! My Ford Bantam 2003 Model 1,6i Xle Rocam Engine Is Overheating Afte...

My ford bantam 2003 model 1,6i XLE rocam engine is overheating after few minutes after I started.Fan tested and is functioning well. When I switch on the aircon the fan works fine & when it goes to re...

141 views with 1 answer (last answer 11 months ago)
roanantelope
5

2008 Generator

2008 Ford bantam charging rate varies from 11.5 to occasionally 13 volts. Could this be fault in Generator please?

35 views with 3 answers (last answer about a year ago)
Swannie57
0

What Type Of Lights Do You Use In The Dashboard?

My dashboard has blown a couple of lights and I'm looking to replace them with LED but no one can tell me what type of pin I need to buy. Any help please?

34 views with 3 answers (last answer about a year ago)
Pieter Hendrik
0

Hi I Have A Ford Bantam Bakkie Its A 1600i Fuel Injection I Dont Get Power ...

253 views with 1 answer (last answer about a year ago)
CHRISSHEARS
40

2010 Wiper Relay,where Is It?

NEED TO FIND THE RELAY,THE WIPERS STOPPED WORKING

130 views with 1 answer (last answer about a year ago)
Lappies007
10

Please Any Help Will Be Much Appreciated

Please any help will be much appreciated I have a 2010 ford bantam base model. I am struggling to start it in the mornings when its cold. the funny part is the heat gauge always goes to half when I ...

129 views with 2 answers (last answer about a year ago)
EnosM
120

I Have Ford Bantam 1.3i 2007, While Driving The Heater Just Comes On Whethe...

I have Ford Bantam 1.3i 2007, while driving the heater just comes on whether the AC is on or not, causing heat in the vehicle. pls. help

224 views with 1 answer (last answer about a year ago)
phills
0

Ford Bantam Brakes

I wondered if i can change my 2011 bantam disk brakes on my own.will i have to bleed the braking system or can i just remove it and fit the new ones?bcoz if i drive normally i have almost no brake...

171 views with 1 answer (last answer about a year ago)
Carbugz
0

Ford Bantam Bakkie Don't Want To Start

My ford bantam bakkie do not want to start at all. No lights going on as well as the lights on the dashboard. Battery working. No sound when turning the key.

270 views with 1 answer (last answer about a year ago)
vmaluleke
20

I Have Problem I Have Changed Oil Pump But Oil Light Still Flashes And Engi...

bantam rocam engine noise I have replaced oil pump but it has noise when Idling or driving

452 views with 1 answer (last answer about a year ago)
Sico
70

Ford Bantam Starting Problems

Hi! I have a 1.3 bantam 2007 model, it only starts when the engine is cold. Ford mechanic tells me to replace the throttle body, solenoid and the starter motor. Could that be the problem?

777 views with 5 answers (last answer about a year ago)
roanantelope
5

Where Is The Ptm Situated On The 2008 Ford Bantam Please?

52 views with 1 answer (last answer about a year ago)
sidonius1
0

Hi ,my Bantam 13 Rocam Has A Computer That Got Wet ,replaced It ,the Bakie ...

Sid van wyk

54 views with 1 answer (last answer about a year ago)
Franie
0

Ford Bantam 2010 Heating Problem

Hi can someone please help me. My bakkie all out of the blue starting to heat up. My husband bought a new Waterpump as this was what the guy at Spares shop told him to get - no luck it is still heat...

152 views with 4 answers (last answer 5 months ago)
Ronnie Ackerman
0

I Removed My Plugwires A Replaced Them Wrong Back.

Ford bantam 2006 1.3i

53 views with 1 answer (last answer 10 months ago)
geldenf
0

How Do I Remove The Steeringwheel Of A Ford Bantam 1.6xle To Replace Indica...

159 views with 1 answer (last answer about a year ago)
spidz69
0

Noise At The Back

After installing new shocks front and back of my ford, a noise appeared it sounds like its coming from below the loading bin. a metal clicking sound, what can be wrong?

70 views with 1 answer (last answer about a year ago)
eezy
0

Anyone Have The Torque Setting For Big End Bearings On Rocam 1.3

270 views with 1 answer (last answer about a year ago)
prev 1 2 3 4 5 ... 10 next

Favorite this topic

Subscribe to Ford Bantam questions.

Shortcuts

Search Ford Bantam Questions

Ford Bantam Experts

#1 FordNut
FordNut
Reputation 580
#2 Joel Mearns
Joel Mearns
Reputation 420
#3 MrRocket12
MrRocket12
Reputation 400
View All