Mazda MAZDASPEED Protege Questions Any type

• • Report

Scottdout asked a Mazda MAZDASPEED Protege Shopping & Pricing question 8 months ago

Where Is A Good Place To Order Parts, Also Will Need Engine Spec's

I have a 2003 Mazdaspeed engine I purphased from a wrecking yard with 87000 on it and I want to replace the timing belt and pull the pan and check the bearings ( as this what went bad with my orginal ...

• • Report

Scottdout asked a Mazda MAZDASPEED Protege Maintenance & Repair question 8 months ago

How Lond Do These Engines Last, Mine Is Blowen Up.

I have approx 60,000 miles on the car and the rod bearings went out and of coarse the crank is ruined and the connecting rods, The oil was full, maybe the oil pump went bad,,Dont know, But I do need a...

• • Report

JEANGEL asked a 2003 Mazda MAZDASPEED Protege 4 Dr Turbo Sedan Shopping & Pricing question 8 months ago

Waste Gate Acturator

WHERE CAN I FIND A WASTE GATE ACTURATOR FOR A 2003 MAZDASPEED PROTEGE. THE VEHICLE HAS A CALLOWAY TURBO INSTALLED?. CAN THE WASTE GATE ACTURATOR BE REBUILT?

• • Report

JEANGEL asked a 2003 Mazda MAZDASPEED Protege 4 Dr Turbo Sedan Maintenance & Repair question 8 months ago

Where Can I Find A Turbo Parts Diagram For A 2003 Mazdaspeed Protege

• • Report

Andrew asked a 2003 Mazda MAZDASPEED Protege 4 Dr Turbo Sedan (2003.5) Maintenance & Repair question about a year ago

Mazda Dealer Ship Broke My Car What Should I Do?

My wiring harness got a hole drilled through it at the mazda dealer ship. Its the main engine emission harness. Mazda has attempted to install the right harness 3 times now with no luck. What should i...

• • Report

Andrew asked a 2003 Mazda MAZDASPEED Protege 4 Dr Turbo Sedan (2003.5) Car Customization question about a year ago

Is It Ok To Paint A Turbo Charger?

Is it ok to paint a turbo charger with engine enamel? or does it need to be powder coated with special extra high heat paint?

• • Report

Raphael asked a 2003 Mazda MAZDASPEED Protege 4 Dr Turbo Sedan (2003.5) General question 4 years ago

Anyone Looking For A Custom Fmic (front Mount Intercooler) With Greddy Bov ...

I have an FMIC kit with all pipes needed and also a flange welded to it with a Greddy BOV. This is a great system and the only reason I am selling it is because I am selling the car and parting it ou...

• • Report

taishinto asked a 2003 Mazda MAZDASPEED Protege 4 Dr Turbo Sedan (2003.5) General question 5 years ago

Performance

What is anyones opinion on the performance of the speed Protege (mainly talking engine but overall is cool too).

• • Report

mspeed1 asked a 2003 Mazda MAZDASPEED Protege 4 Dr Turbo Sedan (2003.5) Maintenance & Repair question 5 years ago

How Do I Change Out The Blown Kenwood Speaker In The Back?

The small sub in the back is blown and I have already unscrewed and unbolted the box from the top of the trunk and I can't get to the speaker.

• • Report

Dan asked a Mazda MAZDASPEED Protege Car Customization question 4 years ago

Engine Mods

Anyone have any experience with mechanical boost controllers on the MSP? Does this work well as a stand alone install? Any good brands/ brands to avoid?

• • Report

Hector asked a Mazda MAZDASPEED Protege Car Customization question 4 years ago

Fuel Cut

Hey any one know how to take the fuel cut in the MSP?