Ford Falcon Questions Any type

  • Newest
  • Recently Active
  • Unanswered
justbobbass
0

What Size Screws Are Used To Hold The Condenser And Points In Place In My 1...

rebuilding my distributor and the screws for the points and condenser are missing. need to know what size and thread,etc.

12 views with 2 answers (last answer 2 days ago)
ehowardal
0

63 Falcon Futura Gauges

Gauges are original but replaced the constant voltage regulator. Temp gauge won't move but when i turn the key to acc the feul gauge rises. When i start the car the feul gauge drops to nothing. Re...

8 views with 1 answer (last answer about a week ago)
Ozcar Metcraft
0

Is My Eb Falcon Rare Or Just A Dealer Special

10 views with 1 answer (last answer 4 weeks ago)
Wilsie48
10

Door Latch

To install a door latch brushing do you have to disassemble the window crank

Wilsie48
10

Door Latch

Trying to replace a door latch brushing that connects the rode from outside handle can it be install without disassemble the hole door latch . Looking for some good tips !!

Bebbajean
0

Will The Fenders Off Of A 1963 Falcon Fit A 1961 Falcon?

34 views with 1 answer (last answer 3 months ago)
glacebay
0

Retaining Clip

the rode coming from outside door handle drives side going to the door latch is there a name for that retaining clip or someone have picture of it .I tried to look at the passage side rode but it is h...

8 views with 1 answer (last answer 3 months ago)
Kameron Randall
0

63 Ford Falcon Front Wheel Bearing Replacement

I have a 63 ford falcon futura with a bad drivers front side wheel bearing. Ive worked on cars before but have never done a bearing could someone help me find out exactly which bearing I need to b...

27 views with 3 answers (last answer 3 months ago)
glacebay
0

Door Latch Retaining Clip

the rod from the outside door handle is disconnected from the door latch retaining clip. the old one still in place . does this mean that I need to replace door latch retaining clip.

26 views with 1 answer (last answer 4 months ago)
Wilsie48
10

Front Will Not Open From Outside

Front drive side door will not open from the outside . The door rode was disconnected from the clip how do you remove and replace the clip

20 views with 3 answers (last answer 4 months ago)
Wilsie48
10

Door Rode Clip

Having problems with a door rode sliping out of the clip how do you remove and replace a new clip

12 views with 1 answer (last answer 4 months ago)
Miller1313
0

61 Falcon Problems Starting

I have replaced the battery,selonoid, starter generator, and wiring to all 3. When I try to start it onlymakes one click, any suggestions to what to do next? By the way headlights work.

48 views with 4 answers (last answer 4 months ago)
jamest7281
0

I Have A 1963 Ranchero And I Want To Convert It From Manual Steering Car To...

81 views with 5 answers (last answer 5 months ago)
Wilsie48
10

Door Handle

Door handle on the driver side is not working .Inside door handle works . Is the problem with the lock rode .And how can you make adjustments

28 views with 2 answers (last answer 5 months ago)
Jimmy004
0

Hi There, My Ford Falcon Ba Xt 2005 Automatic Transmission. Having Problem...

Hi there, My ford falcon BA XT 2005 Automatic Transmission. Having problem is not shifting from 2nd gear to third i my mechanic have scan it he did not find any problem, he said all the four solin...

13 views with 1 answer (last answer 5 months ago)
Radola54
0

How Do I Remove Windwing From My 1963 1/2 Falcon Futura

Windwing removal & installation

57 views with 5 answers (last answer 6 months ago)
Crestblue63
0

How Do I Reinstall The Side Molding For A 63 Falcon Convertible?

I have a 63 ford falcon convertible. I am reinstalling the door and rear fender moldings. I have new clips, but not sure how the molding clips on after I have installed the clips. Do they slide in? ...

49 views with 2 answers (last answer 6 months ago)
Wilsie48
10

Red Wire On Ignition Switch Going To The Battery

The red wire on the ignition switch plug going to the battery needs to be replace .how do i remove old one from the plug

78 views with 3 answers (last answer 7 months ago)
Wilsie48
10

Soldering Or Connectors

Just wondering if it would be ok if I use a insulated connector on a wire from ignition switch instead of soldering have problems soldering thanks

26 views with 4 answers (last answer 6 months ago)
1 2 3 4 5 ... 8 next

Favorite this topic

Subscribe to Ford Falcon questions.

Search Ford Falcon Questions

Ford Falcon Experts

#1 Troy Witt
Troy Witt
Reputation 390
#2 MrBlueOval
MrBlueOval
Reputation 320
#3 Thomas Smith
Thomas Smith
Reputation 130
View All

Related Models For Sale

Used Ford Mustang"
346 Great Deals out of 47,543 listings starting at $1,100
Used Ford Galaxie"
77 listings
Used Porsche Boxster"
69 Great Deals out of 2,014 listings starting at $3,000
Used Chevrolet Camaro"
272 Great Deals out of 26,352 listings starting at $1,900
Used Ford F-150"
2,814 Great Deals out of 196,508 listings starting at $1,600
Used Mazda MX-5 Miata"
68 Great Deals out of 3,267 listings starting at $2,800
Used Ford Torino"
28 listings
Used Ford Shelby GT500"
8 Great Deals out of 734 listings starting at $21,990
Used Ford F-100"
109 listings
Used Ford GT"
44 listings starting at $274,989
Used Ford Pinto"
4 listings
Used MINI Cooper"
313 Great Deals out of 14,215 listings starting at $2,195