Ford Bantam Questions Maintenance & Repair

Ford Bantam Troubleshoot

I had an issue with electrical harness repaired that everything comes on but no power to engen !please help

Ford Bantam Electrical Troubleshoot

Before a fire hazard accrued l was driving around and my hazards starting to indicate and would not go off ,my gages stop working my bakkie was doing its own thing and burst into flames !!! I sav...

Ford Rocam 1.3 Heat Gauge Problem

While driving long distance the heat gauge shows normal working temperature "in the middle". When I switch the bakkie off and start it again after a few minutes the heat gauge rise to almost overhe...

Bantam 2008 Rocam 1.3i

I have a 2008 Bantam rocam 1.3i The battery is being discharged when switched off and stands overnight The battery is new and when fully charged retains charge if positive terminal is disconnected. O...

1985 1.6 CVH Ford Bantam Wont Start

Replaced stardard carb with 32/36 Weber carb, refurbished starter, new ignition module, new coil, plenty fuel and good spark, car wont start at all. Cranks but dont start

What's The Cause Of A Rev Increase ?

Hi, I have a Ford Bantam 1.3i rocam 2008 model. Start the engine, it runs well after a couple of minutes the Rev count goes up to 2000rmp, what may be the cause of this and what can be done to sol...

Battery Light Issues?

I have a 2010 ford bantam 1.3 rocam petrol, I drove to work one morning with all normal. The afternoon when i started, the battery light did not go off, I limped home and measured the output voltag...

My Ford Bantam Cluster Is Working, But When The Battery Is Low It Show

My Ford bantam rocam cluster is not working, but when the battery is low it show, please help.

Ford Bantam Rocam 2010

Hi everyone can you please assist On my Ford bantam 1.3 rocam, I was changing the spark plugs yesterday when we done with changing the spark plugs we attempt to start,it didn't start but the engine...

Electrical Problem Cranks But Won't Start

Hi. I have a 2007 Ford bantam rocam engine. It cranks but won't start. I discovered that the computer box was replace with a bigger box which is for cars pre 2007. I did some research and changed ...

Where Is The Temperature Gage Stay In The Ford Bantam Rocam Engine ?

where is the temperature Gage stay in the ford bantam Rocam engine ?

Oil Supply To Camshaft Can Lobes???

Hi ...I have overhauled my motor...completely... New oil pump...camshaft.. Crank cut..ect. However..it appears that my new camshaft is not being lubricated... Removed tappet cover....and hardly oil o...

How Much Does A Key Reader Cost For A Bantum

Ford Bantam Won't Start

My ford bantam won't start in the mornings. It does not swing, have to kick start it, during the day the bakkie is fine. Auto elect guy said the battery n alternator is fine, gt a new battery BT it...

2006 Ford Bantam 1.3 Rocam

Good day, can someone tell me if the fuel in the fuel rail should be pressurized after the vehicle is switched off. There is no pressure in the fuel rail when i remove my feed and return line, is the...

Need Cylinder Head Gasket Torque Specs. Ford Bantam 1.3 Rocam 2006

need cylinder head gasket torque specs. Ford bantam rocam, 1.3, 2006 model. Stood a while, and oil looks like mud, not starting. Want to change cyl head gasket.

FRONT AXLE AND HUBS AND BEARING

I BOUGHT A 1997 BANTAM LDV BUT I HAVE TO REPLACE THE FRONT AXLES,HUBS AND BEARINGS EVERY 3000KM WHY WHAT IS THE REASON

Ford Bantam 2010 1.3i Xl. Facelift

Hi guys, Often when I try cranking my van, the starter turns in its housing and doesn't seem to kick in, or it kicks in but doesn't actually crank the motor. Security light wise all good goes off ...

Hello All What Is The Price Of A Key Ready

Ford Bantam Door Does Not Open From Outside