Ford Falcon Questions Maintenance & Repair

  • Newest
  • Recently Active
  • Unanswered
wilsie
0

Transmission Fluid Type F

Just wondering if type f transmission fluid m2c33- f or g would be ok to use in a 1963 ford falcon 6 clyinder 170

18 views with 6 answers (last answer about a week ago)
wilsie
0

Bleeding The Brakes

Need to change the brake light switch that is connected to the master cylinder do i need to bleed the braker afterwards

4 views with 2 answers (last answer about a week ago)
Patrick Nunes
0

Ignition Switch Wiring

I have a 63 Ford Falcon and I'm changing the ignition do you to the old one was a Chevy anyway I need to know what prongs are wet so I could do the wiring correct or where I could get a pigtail does...

Patrick Nunes
0

Installing A New Ignition And Keys

I am installing a new ignition and key set and I Ford Falcon 63 the old ignition was from a Chevy the Ford ignition doesn't have the prongs named what they are as the Chevys do as an accessory groun...

wilsie
0

No Brake Lights

I have tail lights ,signal lights but no brake light

18 views with 2 answers (last answer about a month ago)
chris14ono
0

How Can I Get My Turn Signal To Cancel On My 1963 Ford Falcon Futura?

I have replaced the turn signal switch with the canceling cam built into it. I have also replaced the steering wheel with a NOS steering wheel/horn ring. However the steering wheel does not seem to ...

2 views with 2 answers (last answer about a month ago)
chris14ono
0

How Can I Get My Turn Signal To Cancel On My 1963 Ford Falcon Futura?

I have replaced the turn signal switch with the canceling cam built into it. I have also replaced the steering wheel with a NOS steering wheel/horn ring. However the steering wheel does not seem to ...

4 views with 1 answer (last answer about a month ago)
Dylan Hager
0

Door Lock Cylinder

I need some help in changing my door lock cylinder on my 61 ford falcon. Thank you

1 view with 1 answer (last answer about a month ago)
Maureschat
0

Ford Falcon Ute

Bonnet is shut and cable has broken. How do you get in and release bonnet? It's a very tight fit

Samuel Samuel
0

Why My Fan Of A Ford Falcon Futura Making Noisy

Fan noisy

shorecam
0

Thanks -- Knob Shaft Works Normally When Switch Is Out Of Dash, But Slides ...

1962 Falcon Ranchero Knob shaft works normally when switch is out of dash, but slides in and out with no clicks when switch is in dash, like release button is held down (it's not). How...

11 views with 1 answer (last answer 4 months ago)
Cindy Hywood
0

My Car Has New Spark Plugs, And No Other Known Issues But When I Pt My Foot...

has new spark plugs, runs beautiful usually and still does once at speed i want to be at or i am not giving way and taking off.

11 views with 2 answers (last answer 4 months ago)
dlakanen
0

Car Starts But Idles Rough Then Dies Shortly

I don't know too much about Cars but it has a 170 inline 6. it also has an auto lite 1100 recently rebuilt carb. When started it sounds just terrible but it'll run on its own, but will die within t...

13 views with 1 answer (last answer 5 months ago)
chris14ono
0

How Can Gas Be Pumped Into My 1963 For Falcon Futura Without The Pump Neck ...

39 views with 2 answers (last answer 5 months ago)
justbobbass
0

What Size Screws Are Used To Hold The Condenser And Points In Place In My 1...

rebuilding my distributor and the screws for the points and condenser are missing. need to know what size and thread,etc.

18 views with 2 answers (last answer 6 months ago)
ehowardal
0

63 Falcon Futura Gauges

Gauges are original but replaced the constant voltage regulator. Temp gauge won't move but when i turn the key to acc the feul gauge rises. When i start the car the feul gauge drops to nothing. Re...

22 views with 1 answer (last answer 7 months ago)
Kameron Randall
0

63 Ford Falcon Front Wheel Bearing Replacement

I have a 63 ford falcon futura with a bad drivers front side wheel bearing. Ive worked on cars before but have never done a bearing could someone help me find out exactly which bearing I need to b...

67 views with 3 answers (last answer 10 months ago)
glacebay
0

Door Latch Retaining Clip

the rod from the outside door handle is disconnected from the door latch retaining clip. the old one still in place . does this mean that I need to replace door latch retaining clip.

38 views with 1 answer (last answer 10 months ago)
joejanz
0

Horn Only Works When I Push The Clutch Down.

Any suggestions will help. Thanks

7 views with 1 answer (last answer 5 months ago)
1 2 3 4 5 6 next

Favorite this topic

Subscribe to Ford Falcon Mainenance & Repair questions.

Search Ford Falcon Questions

Ford Falcon Experts

#1 Troy Witt
Troy Witt
Reputation 460
#2 MrBlueOval
MrBlueOval
Reputation 340
#3 falconman13
falconman13
Reputation 120
View All

Related Models For Sale

Used Ford Mustang"
660 Great Deals out of 41,187 listings starting at $1,500
Used Chevrolet Impala"
862 Great Deals out of 31,631 listings starting at $995
Used Ford Galaxie"
107 listings
Used Ford Thunderbird"
35 Great Deals out of 1,120 listings starting at $6,995
Used Ford Shelby GT350"
769 listings starting at $50,370
Used Chevrolet Corvette"
336 Great Deals out of 19,147 listings starting at $2,995
Used Ford Torino"
32 listings
Used Dodge Charger"
549 Great Deals out of 31,703 listings starting at $1,800
Used Volkswagen Beetle"
198 Great Deals out of 9,219 listings starting at $600
Used Chevrolet Nova"
166 listings