I got a P0340 on my '96 intrepid ES. Cam position sensor. I replaced it, but still no go. Put the diagnostic machine on, and still I get a P0340 code, even with the new sensor. What gives here?

Asked by Thomas Feb 16, 2013 at 03:58 PM about the 1996 Dodge Intrepid ES FWD

Question type: Maintenance & Repair

I am only getting one code reading on the OBD reader, and that is the p0340.
Not sure what the hell else is wrong, but i am not pushing any other codes.
If I blew my timing belt, i am certain I would have destroyed the car, as the car shut down at 65 mph,
when it died.
I would just have a heavy paperweight if the timing belt went at that speed.
Can anyone tell me what to do next?

205

Robby answered 11 years ago

repair the timing belt i did the samething 2 yrs a go

Mark helpful

Your Answer:

I got a P0340 on my '96 intrepid ES. Cam position sensor. I replaced it, but still no go. Put the diagnostic machine on, and still I get a P0340 code, even with the new sensor. What gives here? 1 Answer

I am only getting one code reading on the OBD reader, and that is the p0340. Not sure what the hell else is wrong, but i am not pushing any other codes. If I blew my timing belt, i am certain I would ...

1996 Dodge Intrepid ES FWD

-

Maintenance & Repair
I have an 04 with the dreaded 2.7 engine. the engine light is on and giving a code for the crank sensor. it has been replaced...twice. the light is still on and they can't even reset it. 1 Answer

I've tried 3 times to erase the code. The light does not go off and I can't get an inspection.

2004 Dodge Intrepid SE FWD

-

Maintenance & Repair
I have A 2000 Dodge Intrepid 2.7 V6 and I drained & changed the thermostat in it bc I had no heat and put antifreeze and water back in let it get warm an still blows ice cold. What do I need to do? 1 Answer

It blows ice cold air when turned to heat and it has never run hot on me since I bought it but it just blows cold air when the knob is turned to heat. Please tell me what I can do next. Thanks.

2000 Dodge Intrepid FWD

-

Maintenance & Repair
OK, I also have a 2003 Dodge Intrepid Interceptor, it has been broken down for a little while with what I was told was a hole in the head gasket. I am debating on if it would be better to sell it or try and get someone to repair it for me. I love this car but its just sitting right now. Hoping for some good advice. There are pictures of it in my garage. 6 Answers

after blowing a radiator hose it wouldn't drive far without over heating, but would sit and idle for ever without heating. Mechanic in New Mexico couldn't figure the problem out for a week and after ...

2003 Dodge Intrepid

-

Maintenance & Repair
my A/C compressor is making alot of noise i have already replaced it once and i have no idea what is wrong it makes a grinding noise all the time.... 4 Answers

its made my car sound like an old beater and i hate it... its a 96 with only 136k miles. i have tryed lubing all the pullies and still its the same loudness and everything

1996 Dodge Intrepid

-

Maintenance & Repair

Own this car?

Share your experience with others.

1996 Dodge Intrepid

Write a car review

Review another car

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.

I got a P0340 on my '96 intrepid ES. Cam position sensor. I replaced it, but still no go. Put the diagnostic machine on, and still I get a P0340 code, even with the new sensor. What gives here?

1 Answer

Your Answer:

Own this car?

Share your experience with others.

Shortcuts

Search Dodge Intrepid Questions

CarGurus Experts

Know more, shop wisely

Used Cars For Sale

I got a P0340 on my '96 intrepid ES. Cam position sensor. I replaced it, but still no go. Put the diagnostic machine on, and still I get a P0340 code, even with the new sensor. What gives here?

1 Answer

Your Answer:

Related Questions