I have a 2006 Impala and just discovered that the heater is only working on the passenger side of the car. Any ideas on what could be wrong?
Question type: Maintenance & Repair
when I switch the air control to heat on the drivers side it is nothing but cold air but when the passenger side is switched to heat it gets hot.
Is there a fuse to check or could this be something under the hood?
4 Answers
Michael answered 4 years ago
Most likely a blend door issue. I had the same problem in my GTP (except I was getting heat on the driver's side). The blend door motor had went out in my case.
Michael answered 4 years ago
It is a job.. I paid to have mine done (mostly because I had spare cash at the time). I googled 'Chevy Blend Door Actuator Replacement' and there are some detailed youtube videos explaining how to do it.
bonsim12 answered 3 years ago
when turning temperature control I hear a ticking noise inside
Your Answer
Related Questions
-
I have a 2006 Impala and just discovered that the heater is only working on the passenger side of the car. Any ideas on what could be wrong? 4 answers
when I switch the air control to heat on the drivers side it is nothing but cold air but when the passenger side is switched to heat it gets hot. Is there a fuse to check or could this be something un...
2006 Chevrolet Impala LT
-
Maintenance & Repair
-
I have a 2010 Chevy Impala & when I turn the heater on it only blows heat on the passenger side not the driver side it also blows heat for a couple of minutes after that it just blows cold on both 3 answers
Sides what could it be? The thermostat, air pumps or...
2010 Chevrolet Impala LT
-
Maintenance & Repair
-
I have a 2005 impala the trac light is on and the abs light what could it be ? 1 answer
I have a 2005 impala the trac light is on and the abs light .Ican turn the car off and press the brake and start the car and all the lights go off untill i release the brake pedal
2005 Chevrolet Impala Base
-
Maintenance & Repair
-
I have a 2000 chevy impala shut the car off and it wouldnt turn over after that is getting no power to the stater wire on the solinoid whats wrong? 2 answers
I have 2000 impala 3.4 will not turn over is not getting power to the stater wire on the solenoid fuses and relays all good when I put an anylizer on it it said it couldn't connect to the vehicle can ...
2000 Chevrolet Impala Base
-
Maintenance & Repair
-
I have a 2000 Impala. When I got the car it seemed to have electrical problems. One issues I%27m worried about is that my blinkers will stop working out of nowhere. When I would put on the signal%2C the arrows on the dash wont respond at all. It would happen on and off when I first got it%2C I would just turn the car off and back on and they would work. A few months went by without a problem%2C then about a week ago it started happening again. They will just stop when I am driving%2C and sometime restarting my car wont help. I%27m not sure what it is%2C or what it will cost to fix. 2 answers
I have a 2000 Impala. When I got the car it seemed to have electrical problems. One issues I'm worried about is that my blinkers will stop working out of nowhere. When I would put on the signal, the ...
2000 Chevrolet Impala LS
-
Maintenance & Repair
Looking for a Used Impala in your area?
CarGurus has 35,645 nationwide Impala listings starting at $899.
Shortcuts
Search Chevrolet Impala Questions
Chevrolet Impala Experts
| #1 |
|
Js08016
Reputation
1,820
|
| #2 |
|
Danny Wang
Reputation
1,680
|
| #3 |
|
Tom Demyan
Reputation
1,660
|
Related Models For Sale
Used Cars For Sale
Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use.