break problems

Asked by zacl1 Oct 13, 2008 at 10:02 PM about the 1992 Plymouth Acclaim

Question type: Maintenance & Repair

i changed the break pads out after taking off the calipers, and break lines...bleed break lines and put new break fluid in...now have no break pressure

- Report

Justin answered 8 years ago

did you make sure that when you were bleeding the brakes that you did not run out of fluid in the DOT-3 container? cause if it did run out, it would have sent air bubbles right back into those brake lines.

1 of 1 people found this helpful.

Mark helpful

115

- Report

Deven answered 8 years ago

Is the brake master cylinder in good condition, and how old is the power booster? If you did all that to the calipers and what not, bled them out the correct way and no fluid leaks, its possible the rubber seal in the power booster is shot and not allowing the brakes to build up pressure.

1 of 1 people found this helpful.

Mark helpful

4,675

- Report

Danny answered 7 years ago

I assume you meant not running out of DOT 3 in the master cylinder while bleeding.

Mark helpful

- Report

Leslie answered 6 years ago

what is the power booster?

2 of 2 people found this helpful.

Mark helpful

Your Answer

stalling problem 5 answers

While drivng down the road, the car just dies. If you wait awhile, it'll start and run again. Could the fuel pump shut of and start again after it cools?

1989 Plymouth Acclaim

-

Maintenance & Repair
1992 Plymouth Acclaim Transmision problem. 2 answers

I have a 1992 Plymouth Acclaim that shifts great until it is warmed up all the way. Then it shifts fine until 2nd to 3rd. It will hang in 2nd until you let off the gas. Filter and Fluid have been chan...

1992 Plymouth Acclaim 4 Dr STD Sedan

-

Maintenance & Repair
Dash lights and gauges go out, signal high beam indicator come on when I put on headlights. Replaced headlight switch still happens . If I hit the middle of the dash with my palm it all works perfectly any ideas where to look next on my 89 plymouth acclaim ? 1 answer

1989 Plymouth Acclaim

-

Maintenance & Repair
bad oil leak, valve covers or head gaskets or something else? 2 answers

hey gang, recently put a new engine in my 1994 plymouth acclaim V6 engine. it was a junkyard engine and ive made it about 2k miles with it sofar. it started burning oil about a week ago, went throug...

1994 Plymouth Acclaim 4 Dr STD Sedan

-

Maintenance & Repair
Is the engine in the 1991 plymoth acclaim a good engine 3 answers

I want to know if this year of car has a good engine

1991 Plymouth Acclaim 4 Dr STD Sedan

-

Shopping & Pricing

Looking for a Used Acclaim in your area?

CarGurus has 3 nationwide Acclaim listings and the tools to find you a great deal.

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use.

#1		Masterofsparks8 Reputation 50
#1		Patsy Jones Reputation 50
#3		T_S_T Reputation 40

break problems

4 Answers

Your Answer

Related Questions

stalling problem 5 answers

1992 Plymouth Acclaim Transmision problem. 2 answers

Dash lights and gauges go out, signal high beam indicator come on when I put on headlights. Replaced headlight switch still happens . If I hit the middle of the dash with my palm it all works perfectly any ideas where to look next on my 89 plymouth acclaim ? 1 answer

bad oil leak, valve covers or head gaskets or something else? 2 answers

Is the engine in the 1991 plymoth acclaim a good engine 3 answers

Looking for a Used Acclaim in your area?

Shortcuts

Search Plymouth Acclaim Questions

Plymouth Acclaim Experts

Used Cars For Sale