GMC Vandura Questions Maintenance & Repair

  • Newest
  • Recently Active
  • Unanswered
bullfrogsblues
0

1992 Vandura 2500 . Tranny Makes A Noise Like Holding Baseball Cards Agains...

wont go into gear. automatic tranns. is there a posibility of a fluid pump out, or a sensor, or is there a vacuum line I need to look for?

9 views with 2 answers (last answer about a week ago)
sk8drive
0

Transmission Has No Reverse

My 91 Vandura recently had the transmission serviced, and now reverse has gone out. The van sat for a long time before I purchased it, so when I first bought it, it needed some sensors replaced, et...

26 views with 1 answer (last answer about a month ago)
joereedy30
0

My 89 Vandura 5.7 Lit. Idle's So High That When I Put It Into Gear It Slams...

Idles high and I can't find any kind of an adjustment screw or anything to adjust. anyone have any ideas?

29 views with 1 answer (last answer about a month ago)
James Wade
0

1991 Gmc Vandura Thermastat .how Do I Replace It

There is a bracket that needs to move to get other blot off

Josephine Fennell
0

My Transmission Is Leaking In The Front.i Replace The Seal.and Its Still Le...

Its a 1991 GMC 5.7 vandura box truck

47 views with 2 answers (last answer 5 months ago)
A_ko
0

Vandura Runs Rich, Smells Gassy, Sometimes Stalls Out At Low Speeds

new here, relatively new to cars but been working on motorcycles for years got a 1990 vandura with a TBI 4.3L V6, had 69k miles on it, had been sitting so i replaced the fuel pump and filter and got ...

124 views with 1 answer (last answer 8 months ago)
pappiejohn
0

Some Times It Starts ...some Times It Doesnt..

replaced dist......fuel pump and filter....idel control... wires...oil senser....fuel pump relay... when it runs it runs perfect ....shut it off it may start it may not.....also check for any bad e...

49 views with 1 answer (last answer 10 months ago)
italianrob
10

Rough Running While In Gear

Hi John.. I have read the past with dragonfly at the top here.. I'm experiencing these same problems as him. . But I don't have. Or can find this gm inline fuel pressure tester. .I can however tel...

210 views with 3 answers (last answer about a year ago)
MountainMarauder
0

Reading Material For A New Gmc 1992 Vandura Owner?

So I just bought my first ever car, which is funnily enough, also my home. There are a lot of little projects I want to do [figure out the solar panel gig, re do the weather stripping round the wind...

118 views with 2 answers (last answer about a year ago)
JnyQst
50

What Is The Half Circle Sensor With My Thermostat?

i replaceed my thermostat & theres this flat peice of metal that looks like a sensor is connected to it. It goes around half of the thermostat opening & the bolts go through it. What is it & does it...

224 views with 9 answers (last answer about a year ago)
Chip Johnson
55

95gm2500 Rear Axle Bearing Race Problem. Drive New Bearing 1\2 & Stopped Re...

Welded trick chisel. In the right position to be a race. all messed up now .chisel marks . Welding slag. measured bearing and housing . correct , the thing is in the way . ??? Tks.

79 views with 1 answer (last answer about a year ago)
Chip Johnson
55

Hi Does Anyone Know The Size Of The Top Injector Oring Gm Tbi 95 Gmc 4.3 Wh...

size of large or top injector o ring gm tbi 1995 4.3

103 views with 3 answers (last answer about a year ago)
Sherri1002
10

How Do I Get My Bed Back Into A Seats

I do t know how to get my bed back into the seats

77 views with 2 answers (last answer 8 months ago)
Perry Minton
0
1 2 3 next

Favorite this topic

Subscribe to GMC Vandura Maintenance & Repair questions.

Search GMC Vandura Questions

GMC Vandura Experts

#1 John Saffrahn
John Saffrahn
Reputation 90
#2 JnyQst
JnyQst
Reputation 50
#2 Js08016
Js08016
Reputation 50
View All