I am trying to pull my engine on a 2001 saturn sc1 but not sure how to separate the motor from transmission. I removed the bolts on the bell housing and bottom flywheel cover plate .

Asked by Tigerrandy May 19, 2014 at 09:47 AM about the 2001 Saturn S-Series 3 Dr SC1 Coupe

Question type: Maintenance & Repair

I have everything loose on motor and transmission. Are there any bolts that need
removed inside flywheel cover?

2,695

Alex answered 9 years ago

The only things bolting the trans together are the 4 studs around the bell housing, the 3 flywheel cover bolts, as well as the 2 bolts from the lower brace underneath both the oil pan and trans. Sometimes the dowel pins will get corroded and seize the motor and trans together. Just work around the mating surfaces with a screwdriver and hammer to get things loose.

1 people found this helpful.

Mark helpful

Your Answer:

I am trying to pull my engine on a 2001 saturn sc1 but not sure how to separate the motor from transmission. I removed the bolts on the bell housing and bottom flywheel cover plate . 1 Answer

I have everything loose on motor and transmission. Are there any bolts that need removed inside flywheel cover?

2001 Saturn S-Series 3 Dr SC1 Coupe

-

Maintenance & Repair
I am trying to find out the the bore size is on a 1.9 dohc engine in a saturn sc2 1992. 2 Answers

trying to figure out the bore size of the 1.9 dohc motor in my 1992 saturn sc

1992 Saturn S-Series 2 Dr SC Coupe

-

Maintenance & Repair
I have a Saturn 1992 SL Sedan with 164,000 miles. I am having a major problem with the car cutting off while I am driving at a fairly constant speed or when I am idling at a stop light. The engine will shut off, along with the power steering and all other electronics. This happens when at a stop light only after I press on the gas to accelerate from a dead stop, but I am able to put the car in neutral and start the car again (sometimes it takes a while to restart). We tried getting the electronic control module repaired, but this did not fix the problem. We checked the oil and it appears to be of the correct viscosity for the engine. We are at our ends as to what needs to be done to fix this dire problem. Thank you for your time! 8 Answers

I have a Saturn 1992 SL Sedan with 164,000 miles. I am having a major problem with the car cutting off while I am driving at a fairly constant speed or when I am idling at a stop light. The engine w...

1992 Saturn S-Series 4 Dr SL Sedan

-

Maintenance & Repair
My 1999 Saturn sc1 heater quit blowing air. Sounds like someone put a stick in the fan to stop it becausew it sounds loud 1 Answer

I have a 1999 Saturn sc1. The heater just stopped working but it sounds like it is trying to blow but doesn't. It just quit. It is rather loud and sounds like the motor wants to do it's job. Just no f...

1999 Saturn S-Series 3 Dr SC1 Coupe

-

Maintenance & Repair
I have a Saturn 2002 Sc1 with an automatic transmission is it going out? 2 Answers

I have a Saturn 2002 Sc1 with an automatic transmission. When switching gears into reverse my engine picks up rmps and doesnt move before like bumping and then going backwards. Then when I start to ...

2002 Saturn S-Series 3 Dr SC1 Coupe

-

Maintenance & Repair

Own this car?

Share your experience with others.

2001 Saturn S-Series

Write a car review

Review another car

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.

I am trying to pull my engine on a 2001 saturn sc1 but not sure how to separate the motor from transmission. I removed the bolts on the bell housing and bottom flywheel cover plate .

1 Answer

Your Answer:

Own this car?

Share your experience with others.

Shortcuts

Search Saturn S-Series Questions

CarGurus Experts

Know more, shop wisely

Related Models For Sale

Used Cars For Sale

I am trying to pull my engine on a 2001 saturn sc1 but not sure how to separate the motor from transmission. I removed the bolts on the bell housing and bottom flywheel cover plate .

1 Answer

Your Answer:

Related Questions